For steps, ramps and floors, in wet or oily areas. Coarse anti slip finish to reduce accidents
|Quantity||Price per item||Discount|
|Bulk discounts applied in basket|
Watco Safety Grip is a heavy duty, coarse textured, anti slip, two pack epoxy resin coatings designed to provide a safe surface both inside and out. Using one high build coat of Safety Grip minimises the risk of accidents throughout the workplace, particularly for wet or oily areas. All grades now carry CE Mark EN 1504-2 and have test results for slip resistance, abrasion, scratch and impact resistance, as well as for adhesion and hardness. They are also chemical resistant and have an A+ VOC emissions rating with a low level of VOC.
|Temperature||Recoat Time||Touch Dry||Light Traffic||Heavy Traffic|
|Safety Grip Rapid||10°C|
|Safety Grip Cold Cure||0°C|
Full Chemical Resistance: 7 days
Light Traffic: foot, trolley, pallet truck, occasional forklift
Heavy Traffic: regular forklift, heavy footfall, parked vehicles
|Suitable for||Concrete well bonded paint, flat metal|
|Finish||Glossy, coarse texture|
|Interior or Exterior||Interior and exterior|
|Primer required||Not usually. See ‘Priming’ section in 'Application'.|
|Composition||2 part, 100% solids epoxy resin|
|Number of components||1 x curing agent, 1 x resin and 1 x anti slip particles.|
|Coverage||5m² per unit|
|Number of coats||1|
|Mix ratio||Safety Grip/Cold Cure: Up to 30 minutes at 20°C. Rapid: Up to 20 minutes at 20°C. Flex: Up to 25 minutes at 25°C.|
|Dry film thickness||Approximately 320 microns|
|Curing time||16 hours at 20°C|
|Minimum application temperature||15°C|
|Shelf life||12 months in unopened containers.|
|Cleaning tools||It is not practical to clean applicators and they should be discarded after use.|
Bare Concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow the surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.
New Concrete – as a guide, new concrete should be left for 8 weeks to dry. The surface should then be prepared using Watco Etch & Clean, thoroughly rinsed and left to dry.
Priming – is not usually required, but for very porous high suction surfaces, such as sand and cement screed, use Watco 4 Hour Epoxy Primer. Concrete should be sufficiently porous to allow the paint to penetrate, so very smooth or power floated concrete is unsuitable unless first primed with Watco Powerfloat Primer.
Painted Surfaces – abrade to remove any weak or loose paint. Check remaining paint is well bonded. Very smooth, glossy paint should be lightly abraded to provide a key. Watco Bio D can be used to remove grease and oil from painted surfaces. Watco Concroff is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint). A trial area is advisable to test compatibility with previous coatings.
Asphalt – new asphalt must be sound and at least 3 months old. If any residual oils remain, the surface should be washed using Watco Concroff. Painted asphalt should be cleaned with Watco Bio D (Concroff can soften paint), and a trial area is advisable to test compatibility with previous coatings.
Metal – remove any rust and flaking material by disc grinding or wire brushing. Apply the coating immediately after preparation to the clean metal surface. Grease or oil can be removed using Watco Bio D. Allow the metal to dry before coating.
Galvanised Metal – Watco Galvaprime must be used to prepare galvanised metal.
Non-ferrous Metals – for advice, please contact our Technical Department.
Remove dirt with a medium stiff broom or light scrubbing machine using detergents if necessary.
Extensive testing is what makes us the most highly qualified paint and repair manufacturer on the market. Our tests cover just about everything you might want to know about a floor coating – how well it bonds to the floor, how durable it is, how well it stands up to scratching and much more.
Our key tests for Safety Grip:
Learn more about the tests we carry out and how to read the results here.
Full test results can be found on the Technical Data Sheet.
Medium pile roller and tray for applying floor and wall paints
£10.85 (Ex VAT)