Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.
We're open and here to help. Read our COVID-19 service update here.

Watco Safety Coat Cold Cure

Make slippery floors safe during the winter months

  • 2-part polyaspartic resin cures at minus 10°C
  • Ideal for walk-in fridges and cold stores
  • Excellent abrasion and UV resistance

Frequently bought together


Watco Safety Coat Cold Cure is a new type of anti slip resin formulation that can be applied as low as minus 10°C. This high performance coating can be applied in cold conditions where conventional coatings will fail to dry. It is most suited for use in heavily trafficked unheated areas such as workshops, warehouses, loading bays and cold stores. If a coarser textured finish is required for spillage areas or ramps, please see instead Watco Safety Grip Cold Cure (wet PTV 69). 

Safety Coat Cold Cure is extremely resistant to UV and has excellent resistance to weathering, making it a versatile, all year round coating. The finely textured particles are spherical; this makes it easier to keep clean compared to other anti slip coatings which contain a coarse, more angular type grit. Safety Coat Cold Cure carries CE Mark EN1504-2 and has impressive test results for slip resistance, abrasion and impact resistance, as well as for adhesion and hardness.

Recommended areas of use

  • Walk in fridges and freezer
  • Cold stores
  • Production areas
  • Loading bays
  • Unheated areas
  • Warehouses and workshops


  • High performance, two part, anti slip, polyaspartic resin formulation
  • Easy clean, anti slip surface
  • Can be applied at temperatures as low as -10°C and as high as 25°C
  • Excellent resistance to UV and weathering
  • Fast curing – ready for heavy traffic in just 16 hours
  • Superior abrasion and scratch resistance
  • Extremely strong – easily copes with forklift trucks
  • Superior performance demonstrated by ISO testing to CE Mark EN1504-2
Properties Heavy duty, anti-slip finish, easily applied, chemical resistant.
Suitable for Floors, ramps, steps.
Interior or Exterior Interior and exterior.
Primer required No.
Coverage Approx. 25m² per coat per 2.5L unit onto a non-porous surface or 10-15m² onto a porous or textured surface. Coverage will also be reduced if applying in temperatures below 0°C.
Number of coats 2
Curing time 24 hours at 15°C.
Minimum application temperature minus 10°C
Pot life Up to 30 minutes at 20°C.

Surface preparation

Bare concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow the surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff®, again, flush with clean water and allow the surface to dry. 

New concrete – as a guide, new concrete should be left for eight weeks to dry. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this coating. 

Painted surfaces – abrade to remove any weak or loose paint and check remaining paint is well bonded. Watco Bio-D can be used to remove grease and oil from painted surfaces. Watco Concroff® is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint). 

Application in low temperatures – if applying in cold conditions the product should ideally be stored in a warm room for at least 8 hours prior to use. Below 5°C it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. 

Priming – is not usually required, but for open textured, or very porous high suction surfaces, such as sand and cement screed, use Watco Polyaspartic Primer to ensure a uniform finish and to prevent air entrapment bubbles. Watco Polyaspartic Primer should also be used to improve adhesion on smooth (but not power floated) concrete. 

Metal – remove any rust or flaking material by disc grinding or wire brushing. Apply the coating immediately after preparation to the clean metal surface. Grease or oil can be removed using Watco Bio-D. Allow the metal to dry before coating. 

Galvanised Metal – Watco Galvaprime must be used to prepare galvanised metal. Non-ferrous Metals – for advice, please contact our Technical Department. 

Wood – must be sound, clean and dry. If applying to ridged decking, please ensure that the grit particles are spread evenly across the surface.


Mix between 10°C and 15°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin, (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or similar wide bladed tool, (a piece of wooden batten is ideal). Mix between 10°C and 15°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin, (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or similar wide bladed tool, (a piece of wooden batten is ideal). At this point add the unit of anti slip polymer additive. Continue mixing until an even colour and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the side and bottom of the tin. Do not dilute unless you are stirring in the additive as described under ‘Application in low temperatures’. 


Apply between -10°C and 25°C. Empty the mixed components into a paint tray and apply to the floor using a short pile roller, (not a medium pile or foam), ‘working out’ the coating into a thin paint film. A paint brush can be used for cutting in. Do not apply the paint too thickly since this will reduce the slip resistant properties and result in reduced coverage. A feature of polyaspartic coatings is that they should be applied as a thin film. The second coat should be applied as soon as the first coat is dry (generally 6 hours at 20°C), but it must be applied within 5 days. If more than 5 days elapse, the first coat should be lightly abraded.

£121.80 (Ex VAT)

In stock

Do you know the size of the area?

Tools and accessories

Watco Etch & Clean

Watco Etch & Clean

Essential for preparing bare concrete ready for painting

£24.20  (Ex VAT)

Paint Brush

Paint Brush

Professional paint brushes suitable for all coatings

From £2.20  (Ex VAT)

Watco Paint Mixer

Watco Paint Mixer

A manual mixer for thorough mixing of two-part coatings

£3.00  (Ex VAT)

Watco Painting Kit

Watco Painting Kit

Everything you need to help with floor painting

From £41.00  (Ex VAT)

Help & Advice

Contact our friendly and professional Technical Advisors for expert help and advice for your project. You can give us a call on 01483 418 418 or email

Contact us