Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.

Watco Cold Set Coating

For cold areas such as walk-in fridges, cold stores and loading bays. Highly wear resistant

  • Allows essential maintenance during the winter
  • Ideal for use in chiller rooms
  • Excellent abrasion and UV resistance
  • Latest 2-part polyaspartic resin technology
Delivery options
Next day delivery slots available upon request. Call us on 01483 418418 for details.
Frequently bought together


Watco Cold Set Coating uses the latest polyaspartic resin technology to provide a high quality, highly wear resistant coating that can be applied at low temperatures. It is ideal for refurbishment and maintenance in unheated areas during the winter months when conventional coatings will fail to dry.

Recommended areas of use

  • Refurbishment and maintenance in unheated areas
  • As a coating in walk-in fridges, cold stores and loading bays


  • Withstands heavy wear and tear
  • Excellent chemical resistance
  • Can be applied between -10°C and +30°C
  • Fast curing
  • Exceptional UV resistance makes it ideal for exterior application as it resists chalking, weather and fading


Properties Cures at -10°C
Suitable for Concrete, old asphalt/tarmac, well bonded paint, some metals, wood
Finish Glossy, smooth
Interior or Exterior Exterior, Interior
Primer required No primer required
Composition 2 part polyaspartic resin
Coverage 25m² per 2.5L per coat
Recommended number of coats 2
Dry film thickness 85 microns
Curing time (at 0°C) 24 hours
Minimum application temperature -10°C


Surface preparation

All the surfaces must be -10°C or above and free from ice or water. The concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry.

Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Etch & Clean to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Etch & Clean.

Watco Powerfloat Primer is recommended on power floated surfaces but it must be fully cured before over-coating. Previously painted surfaces should be diamond grinded thoroughly prior to application to achieve a consistently rough profile, and ensure all weakly bonded material is removed. Glossy or inadequately prepared surfaces may cause adhesion issues, so a thorough inspection is recommended to ensure no areas are missed, a bristle blaster can be used in any hard-to-reach areas. Thoroughly sweep the area following grinding; any loose material or dust can compromise adhesion.Bio-D can be used to remove any grease and oil from the surface following the grinding process, however, surfaces washed with Watco Bio D must be then thoroughly rinsed with water and allowed to dry fully, prior to coating.

A trial area is advisable to test compatibility with previous coatings.

Below 5°C it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. Do not apply outside if rainfall is imminent.


Only mix in temperatures between 10°C and 25°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or a similar wide bladed tool (a piece of wooden batten is ideal). Continue mixing until an even colour and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute.


If appearance is critical we recommend the application of a small trial area first.

Only apply in temperatures between -10°C and +30°C. The viscosity will be somewhat thicker at very low temperatures, slightly reducing coverage.



Ask a question


Be the first to ask a question...

Ask a question
0 questions / 0 answers

£151.70 (Ex VAT)

In stock

Do you know the size of the area?
Delivery options
Next day delivery slots available upon request. Call us on 01483 418418 for details.

Specialist alternatives

Need slip resistance?

Ensure you have the right safety surface for your floor

A slip resistant surface is ideal for areas that are prone to spills and take regular footfall. Avoid slips with a safe anti slip coating formulated to keep you on your feet and not on the floor.

All anti slip

Watco Safety Coat Cold Cure


Fine textured high performance coating for cold stores, walk-in fridges. Dries at -10°C

From £157.05 (Ex VAT)

Tools and accessories

What our customers say

Watco Cold Set Coating

All the latest news and offers

Subscribe to our newsletter and receive 10% off your next order!