Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.
Lockdown service update: We remain open for business and are here to help Learn more.
x

Watco Safety Coat Food Safe

A safety surface certified for use in food storage areas

  • Meets requirements for EN14/3 (Food taint test)
  • Excellent abrasion and UV resistance
  • Can be applied at a temperature range of minus 10-30°C

Frequently bought together

Description

Watco Safety Coat Food Safe uses the latest polyaspartic resin technology for a high quality, highly wear resistant coating that has been tested and has EN71/3 and taint test certification. It will cure in refrigerated areas (down to -10ºC) where other conventional paints will fail to dry.

This is an anti slip version of Watco Food Safe Coating

Recommended areas of use

  • Food preparation environments
  • Cold food storage such as walk-in fridges
  • Areas where spillages sometimes occur, the finely textured surface is easier to clean than conventional 'gritty' surfaces

Features

  • Tested to EN71/3 as a non-toxic product
  • Takes heavy wear and tear
  • Fast curing, re-coatable in only 5 hours
  • Can be applied between -10ºC and 30ºC
  • Slip resistant
  • Excellent chemical resistance
  • Steam cleanable
Pendulum Slip Test Values
Dry PTVWet PTV
65 Low slip potential 45 Low slip potential 
Specification
Interior or Exterior Interior and exterior.
Coverage 25m² per 2.5L unit.
Number of coats 2
Curing time 6-8 hours at 20ºC.
Pot life Up to 25-30 minutes at 15°C.
Application

Surface preparation

All surfaces must be -10°C or above and free from ice or water. Concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio-D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry.

Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Etch & Clean to ensure adequate Adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Etch & Clean.

Watco Powerfloat Primer is recommended on powerfloated surfaces but it must be fully cured before overcoating. Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatibility with previous coatings.

Below 5°C it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. 

Mixing

Mix between 10°C and 25°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or a similar wide bladed tool (a piece of wooden batten is ideal). Continue mixing until an even colour and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute.

Application

If appearance is critical we recommend the application of a small trial area first.

Apply between -10°C and +30°C. The viscosity will be somewhat thicker at lower temperatures, reducing the coverage rates. The product should be worked out with a short pile roller to maximise the coverage and get the best performance from the product.

£123.20 (Ex VAT)

In stock

Do you know the size of the area?

Specialist alternatives

Prefer a smooth surface?

Get the right finish for your floor

If you are looking for an attractive smooth finish than you will find it here at Watco. We dont just specialise in Anti Slip, but high performance smooth coatings to.

Shop paint

Watco Food Safe Coating

A specialist coating certified for use in food storage areas

From £117.60 (Ex VAT)

Tools and accessories

Watco Cleaning Solvent

Watco Cleaning Solvent

A xylene based solvent to help with cleaning and preparation

From £23.80  (Ex VAT)

Watco Etch & Clean

Watco Etch & Clean

Essential for preparing bare concrete ready for painting

£24.20  (Ex VAT)

Watco Painting Kit

Watco Painting Kit

Everything you need to help with floor painting

From £41.00  (Ex VAT)

12" Roller Frame & Handle

12" Roller Frame & Handle

A sturdy roller applying floor coatings

From £7.70  (Ex VAT)

Watco Paint Mixer

Watco Paint Mixer

A manual mixer for thorough mixing of two-part coatings

£3.00  (Ex VAT)

Stiff and Soft 12" Brooms

Stiff and Soft 12" Brooms

For cleaning or applying Watco universal sealer dustproofer

From £10.50  (Ex VAT)

Help & Advice

Contact our friendly and professional Technical Advisors for expert help and advice for your project. You can give us a call on 01483 418 418 or email sales@watco.co.uk

Contact us

Subscribe