Fast, pourable and strong repairs for heavy wear areas
Total price
£163.00 (Ex VAT)
Flowpatch® is an easy to mix pourable material, ideal for quick repairs to level concrete, inside or outside. Its very strong formula will harden quickly and will accept heavy traffic including forklifts only 2 hours after application.
We recommend Watco Flowpatch Deep Fill® for repairing or levelling deeper holes between 10-200mm in concrete flooring.
| Properties | Quick setting, pourable patch repair for heavily trafficked floors, just add water, mix and pour, slip resistant finish, sets at low temperatures. |
| Suitable for | Concrete |
| Interior or Exterior | Interior and exterior |
| Primer required | No primer required. |
| Composition | Reinforced cement & polymer powder |
| Coverage | Approximately 0.5m² at 25mm thick per 25kg |
| Curing time | 1 hour at 15°C |
| Minimum application temperature | 5°C |
The substrate should be clean and free from oil or contaminants. Any loose material should be removed from the surface. If possible wire brush the surface. Edges of the repair should be cut to depth to avoid feather edging in heavy wear areas. Watco Flowpatch can be applied to damp (not wet) concrete.
Remove the bag of powder from the plastic bucket and use the empty bucket or other suitable container for mixing. To mix, add the powder to water. Use a ratio of 175–225ml of clean cold water to 1kg of powder (as a guide approx. 3.5 units of powder by volume to 1 unit of water).
Due to the short working life of the mixed product, we recommend you carry out the mixing near to the repair, not near to the water source. It’s also useful to have a bucket of water nearby, so you can quickly immerse and clean the tools after use. Put the water into the empty bucket or container and gradually add the powder stirring constantly to achieve a pourable slurry. For small quantities mix by hand using a flat bladed tool such as a spatula, and for larger quantities use a mixer fitted into a slow speed electric drill. Do not add excessive water or drying time will be extended and the performance may be impaired. As the mixture hardens quickly, pour the Flowpatch into the hole to be repaired immediately. We do not recommend re-stirring as this could potentially weaken the final repair. Do not mix more than you can use within a few minutes (5–10 minutes at 20°C). The remaining powder can be stored for future use.
When a smooth consistency is achieved, simply pour Watco Flowpatch in to the hole. If the product has been properly mixed it will self level and will need minimal trowelling. Watco Flowpatch can be applied to any depth between 5mm and 100mm, Flowpatch Deepfill can be applied to depths of 10-200mm. Repairs in lightly trafficked areas can be feather edged, but thin edges are not recommended for medium or heavily trafficked repairs.
Extensive testing is what makes us the most highly qualified paint and repair manufacturer on the market. Our screeds and repair products are tested in areas of tensile, compressive strength and flexural strength.
Our key test for Flowpatch:
Typical compressive strength at 20°C:
| Day 1 | >20N/mm2 |
| Day 7 | >35N/mm2 |
| Day 28 | >45N/mm2 |
Learn more about the tests we carry out and how to read the results here
| Quantity | Price per item | Discount |
|---|---|---|
| 1+ | £123.50 | - |
| 6+ | £111.20 | Save 10% |
| 18+ | £98.80 | Save 20% |
| Bulk discounts applied in basket | ||
|
|
|
|
|
|
|---|---|---|---|---|
|
This product:
Watco Flowpatch |
Watco Bitu-Mend® Pothole Repair |
Watco Concrex Asphalt Repair |
Watco Concrex® Carbon Fibre - Epoxy Repair Mortar |
|
|
From £47.30 (Ex VAT) |
From £56.10 (Ex VAT) |
£199.00 (Ex VAT) |
From £99.00 (Ex VAT) |
|
|
Please make a product selection to continue |
View | View | View | |
| Composition | Reinforced cement & polymer powder | Single pack bitumen & aggregate blend | 2 part epoxy resin plus aggregate | Two part epoxy resin |
| Durability | Heavy | Heavy | Extreme | Extreme |
| Suitable for asphalt & concrete | Concrete | Both | Both | Concrete |
| Deep fill version available | ||||
| How applied | Pour | Shovel and tamper | Trowel | Trowel |
| Cold setting version available | N/A | |||
|
Please make a product selection to continue |
View | View | View |
Our Deep Fill alternatives allow you to apply them at much thicker depths in one application. Meaning you can get a more economical formula that delivers the same strength and reduces downtime.
All hole repairOur chemists have developed cold curing products with the latest resin technology so you can continue with your repair projects all year round.
All cold cureIf you are repairing an asphalt substrate, then we have a range of bitumen based products that help blend in with the existing environment.
All asphalt repair
For mechanical mixing of Watco Flowtop and Watco Flowpatch
£11.90 (Ex VAT)
Ideal for smoothing and levelling off repair materials
£7.20 (Ex VAT)
Contact our friendly and professional Technical Advisors for expert help and advice for your project. You can give us a call on 01483 418 418 or email sales@watco.co.uk
Contact us
